Evaluation of K3^2 in S by SW enclosure

Latching Solinoid Driver
rpu_bus
Posts: 188
Joined: Sun Sep 18, 2016 6:07 pm

Evaluation of K3^2 in S by SW enclosure

Postby rpu_bus » Thu Apr 20, 2017 11:49 am

Swapped K3^1 out for K3^2. It is controlled by a RPUno^5 and has a RS-422 connection using RPUadpt^5. The colored wires on the IDE cable show what is going on much better.

K3^2+RPUno^5+RPUadpt^5_WithValvesPvBat.jpg
K3^2+RPUno^5+RPUadpt^5_WithValvesPvBat.jpg (93.43 KiB) Viewed 299 times


The K3^1 had some hacks to make it work, but the K3^2 is clean and the data from the first few days agree with what the hacked K3^1 was doing.

Code: Select all

Using three Orbit 58874N valves
Location: SxSWEncl (S by SW enclosure)
K3^2, RPUadpt^4 at address '1', RPUno^5 Solenoid program has these save (eeprom) settings

/1/save 1,10
{"K1":{"delay_start_sec":"1","runtime_sec":"150","delay_sec":"3450","cycles":"10"}}
/1/save 2,10
{"K2":{"delay_start_sec":"600","runtime_sec":"150","delay_sec":"3450","cycles":"10"}}
/1/save 3,10
{"K3":{"delay_start_sec":"1200","runtime_sec":"150","delay_sec":"3450","cycles":"10"}}

4/18/2017:23:11 night
/1/flow? 1
{"K1":{"cycle_state":"0","cycles":"0","flow_cnt":"11927"}}
/1/time? 1
{"K1":{"cycle_state":"0","cycles":"0","cycle_millis":"1500001"}}
/1/flow? 2
{"K2":{"cycle_state":"0","cycles":"0","flow_cnt":"48021"}}
/1/time? 2
{"K2":{"cycle_state":"0","cycles":"0","cycle_millis":"1500000"}}
/1/flow? 3
{"K3":{"cycle_state":"0","cycles":"0","flow_cnt":"50389"}}
/1/time? 3
{"K3":{"cycle_state":"0","cycles":"0","cycle_millis":"1500001"}}
/1/analog? 7,6,3,2
{"PWR_V":"12.71","PV_V":"0.88","DISCHRG_A":"0.032","CHRG_A":"0.000"}

4/19/2017:20:35 night
/1/flow? 1
{"K1":{"cycle_state":"0","cycles":"0","flow_cnt":"11923"}}
/1/time? 1
{"K1":{"cycle_state":"0","cycles":"0","cycle_millis":"1500000"}}
/1/flow? 2
{"K2":{"cycle_state":"0","cycles":"0","flow_cnt":"48159"}}
/1/time? 2
{"K2":{"cycle_state":"0","cycles":"0","cycle_millis":"1500000"}}
/1/flow? 3
{"K3":{"cycle_state":"0","cycles":"0","flow_cnt":"50693"}}
/1/time? 3
{"K3":{"cycle_state":"0","cycles":"0","cycle_millis":"1500001"}}
/1/analog? 7,6,3,2
{"PWR_V":"12.74","PV_V":"0.91","DISCHRG_A":"0.032","CHRG_A":"0.000"}

Return to “K3”

Who is online

Users browsing this forum: No registered users and 1 guest